Crankshaft Front Oil Seal Service Kit For Cummins Engine QSB6.7 6BT5.9 3937111 3904351 3900709 3904353 4991305 3935959

When a workshop orders a Cummins part, there are usually three options on the table: a genuine Cummins part, a genuine part remanufactured by Cummins and sold as ReCon, or an aftermarket part produced by another manufacturer. On the surface they look interchangeable. Under the surface they are not, and the difference shows up at exactly the wrong moment — usually with an engine open on the workshop floor and a truck waiting on the road.

What “will-fit” actually means

Most aftermarket manufacturers copy a part closely enough that it will physically fit. The problem is that fitting is not the same as meeting specification. Cummins publishes dimensional and material requirements for every component, and a part that fits but does not meet those requirements can fail in ways that are far more expensive than the price difference saved.

What the laboratory testing showed

Cummins has tested more than 200 non-genuine components for its K-Series engines, covering pistons, rings, valves, cylinder liners, connecting rods and pins, plus small items such as springs and retaining clips. The result was consistent: the parts were dimensionally acceptable, but they did not meet Cummins specifications in materials and design. The documented failures are worth knowing, because each one ends a day of workshop time:

  • Piston ring carrier debonding — the ring carrier separates from the piston body, which can lead to catastrophic engine failure.
  • Out-of-specification ring angles and oil ring sizes — insufficient sealing, excess fuel consumption and reduced performance.
  • Out-of-specification piston bowl dimensions — excess heat, cracking, high fuel consumption and visible smoke.
  • Cracking and misalignment in the piston microstructure — visible in metallographic examination before the part is even fitted.
  • Erosion of the cylinder liner outer surface — a path for coolant to contaminate the oil.
  • Lead pooling in the connecting rod bearing microstructure — a probable cracking mechanism in the bearing.

Each of these is a failure that happens after the invoice has been paid, usually after the part has been fitted, and usually on the machine that was supposed to go back to work the same afternoon.

What ReCon actually is

ReCon is not a third-party rebuild. A ReCon part originates from a genuine Cummins unit and goes through disassembly, inspection, cleaning, calibration and testing to meet the same specifications as a new Cummins part. A ReCon engine is completely disassembled, inspected, cleaned, tested, painted and brought back to like-new condition in a Cummins remanufacturing facility, with the latest ReCon or new parts, a warranty, and zero hours on the clock.

Two practical points follow from that. First, a ReCon engine typically carries the latest engineering updates and improvements, so it is not simply an older engine with a new paint job. Second, remanufacturing is genuinely cheaper for the customer and far cheaper for the environment: up to 85 percent of an engine can be remanufactured, and it takes far less energy and natural resources to extend the life of an engine than to build a new one.

A practical decision framework

Situation Recommended option Why
Cylinder head, crankshaft, turbocharger on a high-hour machine Genuine or ReCon These are the parts that determine whether the engine survives its next rebuild interval, and where a material defect is most likely to be catastrophic.
Complete engine replacement, tight schedule ReCon engine Same specification, zero hours, warranty, and usually available or ordered for fast turnaround rather than built from scratch.
Filters, belts, gaskets, sensors and other consumables Either, provided the specification is met Value here is more about consistent supply and correct cross-reference than about metallurgy.
Budget-driven rebuild of an older machine with a planned second life Aftermarket, with the wear items on genuine or ReCon The sensible compromise is a good cylinder head, rings and bearings with quality replacements elsewhere. We will tell you exactly where that line sits.

How we handle it in practice

When you send us a part number, we tell you which version you are getting and what the trade-offs are. If the budget matters more than the operating environment, we will say so. If the machine is working in a mine, a generator set running continuously, or a truck that cannot afford to be off the road, we will recommend the genuine or ReCon option and explain the failure mode you are avoiding. See our Cummins cylinder heads, pistons and connecting rods and complete engine assemblies for the parts this applies to, or send us the part number directly.

Related reading: Cummins 6BT engine parts and frequently asked questions about Cummins parts.